//! Feeds back the input stream directly into the output stream.
//!
//! Assumes that the input and output devices can use the same stream configuration and that they
//! support the f32 sample format.
//!
//! Uses a delay of `LATENCY_MS` milliseconds in case the default input and output streams are not
//! precisely synchronised.

use clap::Parser;
use cpal::{
    traits::{DeviceTrait, HostTrait, StreamTrait},
    HostUnavailable,
};
use ringbuf::{
    traits::{Consumer, Producer, Split},
    HeapRb,
};

#[derive(Parser, Debug)]
#[command(version, about = "CPAL feedback example", long_about = None)]
struct Opt {
    /// The input audio device to use
    #[arg(short, long, value_name = "IN")]
    input_device: Option<String>,

    /// The output audio device to use
    #[arg(short, long, value_name = "OUT")]
    output_device: Option<String>,

    /// Specify the delay between input and output
    #[arg(short, long, value_name = "DELAY_MS", default_value_t = 150.0)]
    latency: f32,

    /// Use the JACK host. Requires `--features jack`.
    #[arg(long, default_value_t = false)]
    jack: bool,

    /// Use the PulseAudio host. Requires `--features pulseaudio`.
    #[arg(long, default_value_t = false)]
    pulseaudio: bool,
}

fn main() -> anyhow::Result<()> {
    let opt = Opt::parse();

    // Jack/PulseAudio support must be enabled at compile time, and is
    // only available on some platforms.
    #[allow(unused_mut, unused_assignments)]
    let mut jack_host_id = Err(HostUnavailable);
    #[allow(unused_mut, unused_assignments)]
    let mut pulseaudio_host_id = Err(HostUnavailable);

    #[cfg(any(
        target_os = "linux",
        target_os = "dragonfly",
        target_os = "freebsd",
        target_os = "netbsd"
    ))]
    {
        #[cfg(feature = "jack")]
        {
            jack_host_id = Ok(cpal::HostId::Jack);
        }

        #[cfg(feature = "pulseaudio")]
        {
            pulseaudio_host_id = Ok(cpal::HostId::PulseAudio);
        }
    }

    // Manually check for flags. Can be passed through cargo with -- e.g.
    // cargo run --release --example beep --features jack -- --jack
    let host = if opt.jack {
        jack_host_id
            .and_then(cpal::host_from_id)
            .expect("make sure `--features jack` is specified, and the platform is supported")
    } else if opt.pulseaudio {
        pulseaudio_host_id
            .and_then(cpal::host_from_id)
            .expect("make sure `--features pulseaudio` is specified, and the platform is supported")
    } else {
        cpal::default_host()
    };

    // Find devices.
    let input_device = if let Some(device) = opt.input_device {
        let id = &device.parse().expect("failed to parse input device id");
        host.device_by_id(id)
    } else {
        host.default_input_device()
    }
    .expect("failed to find input device");

    let output_device = if let Some(device) = opt.output_device {
        let id = &device.parse().expect("failed to parse output device id");
        host.device_by_id(id)
    } else {
        host.default_output_device()
    }
    .expect("failed to find output device");

    println!("Using input device: \"{}\"", input_device.id()?);
    println!("Using output device: \"{}\"", output_device.id()?);

    // We'll try and use the same configuration between streams to keep it simple.
    let config: cpal::StreamConfig = input_device.default_input_config()?.into();

    // Create a delay in case the input and output devices aren't synced.
    let latency_frames = (opt.latency / 1_000.0) * config.sample_rate as f32;
    let latency_samples = latency_frames as usize * config.channels as usize;

    // The buffer to share samples
    let ring = HeapRb::<f32>::new(latency_samples * 2);
    let (mut producer, mut consumer) = ring.split();

    // Fill the samples with 0.0 equal to the length of the delay.
    for _ in 0..latency_samples {
        // The ring buffer has twice as much space as necessary to add latency here,
        // so this should never fail
        producer.try_push(0.0).unwrap();
    }

    let input_data_fn = move |data: &[f32], _: &cpal::InputCallbackInfo| {
        let mut output_fell_behind = false;
        for &sample in data {
            if producer.try_push(sample).is_err() {
                output_fell_behind = true;
            }
        }
        if output_fell_behind {
            eprintln!("output stream fell behind: try increasing latency");
        }
    };

    let output_data_fn = move |data: &mut [f32], _: &cpal::OutputCallbackInfo| {
        let mut input_fell_behind = false;
        for sample in data {
            *sample = match consumer.try_pop() {
                Some(s) => s,
                None => {
                    input_fell_behind = true;
                    0.0
                }
            };
        }
        if input_fell_behind {
            eprintln!("input stream fell behind: try increasing latency");
        }
    };

    // Build streams.
    println!("Attempting to build both streams with f32 samples and `{config:?}`.");
    let input_stream = input_device.build_input_stream(config, input_data_fn, err_fn, None)?;
    let output_stream = output_device.build_output_stream(config, output_data_fn, err_fn, None)?;
    println!("Successfully built streams.");

    // Play the streams.
    println!(
        "Starting the input and output streams with `{}` milliseconds of latency.",
        opt.latency
    );
    input_stream.play()?;
    output_stream.play()?;

    // Run for 10 seconds before closing.
    println!("Playing for 10 seconds... ");
    std::thread::sleep(std::time::Duration::from_secs(10));
    drop(input_stream);
    drop(output_stream);
    println!("Done!");
    Ok(())
}

fn err_fn(err: cpal::StreamError) {
    eprintln!("an error occurred on stream: {err}");
}